Hair cutting methods

Different hair styles are varied, short and long. The story can be straight, or layered, and the selection of the story depends on the fashionable style and the shape of the face.
To get a nice story, you should deal with a reliable hairdresser, talk to him about the desired story, and tell him stories of the story from different angles, so that it does not end with a short hair story or uneven lengths.

Traditional Short Hair Cutting Method

One of the shortest but not very short stories, bob hair cut, looks nice to those who have a light or medium-density hair, and a heavy-haired woman should avoid this story.
To begin cutting traditional short hair, apply the following steps (cutting classic bob):

The hair is prepared for cutting by moistening it with a spray of water spray without leaving the hair dripping water.
Divide the hair into four parts using the comb and tie each part separately.
A small portion of the back is taken using the comb and the hair is combed down on the neck.
Start cutting from the middle using the comb, where the hair cuts straight from the middle to the outside of the edge, and in the end be sure to straighten the cut and equal.
Another part is combed above the previously cut part and cut with the same straightness and repeated every time until the entire hair is finished to get a short traditional hair story.

The way the story is included for long hair

To cut stratified layers of long hair, this method can be followed by the technique of the basic chord, which is used to measure the length of the story until the layer is equal, and this method is suitable for cutting short hair as well, and the method is:

Moisturize the hair with a spray of water spray, and then comb with a fine tooth comb.
Divide the hair into five equal parts by using the comb and connecting each part with the hair clips by making a part of the upper half of the head, part over each of the ears, two parts in the middle back of the head, or seven parts of the thick hair by doing a middle part in the middle and part above each ear , Three parts in the middle region of the back of the head, the bottom part of the head.
The bottom part, holding a small hair follicle in the middle of the lower part, will be the first staple; the core follicle moves with the cut cut and the newly cut cuttings are the core each time and are placed next to another strand of hair and used as a ruler.
The length of the bottom layer, when determining the length of three different layers of hair, should be remembered. The shorter the hair, the smaller the difference between the layers. The three layers in the long hair vary from 2 to 4 inches. just one.
The fingers are inserted between the middle fingers and the index finger in the hand that is not normally used. If the person is in the right hand, touch the left hand, then move the fingers downwards by moving the stalk at 90 degrees angle until the desired length is reached. Hair.
Cut the remainder of the bottom, using the newly cut staple to cut the next truss, enter the basic chisel with the desired clipping between the index finger and the middle and move the fingers towards the ends by tightening the hair by measuring the angle of 90 ° until reaching the end of the base chute, The length of the basic chisel becomes the new chord, until the entire bottom is cut. Each period of hair is equal to the length of the hair so that it pulls the hair in different directions and at different angles and subtracts any uneven lengths before moving to a new crease. T.
The length of the second layer of hair is determined by removing the left part and leaving it to hang over the bottom layer. The bottom layer is used as a guide to determine the amount of hair to be cut, and the length of the layers varies from 2-4 inches in long hair and half to inches in short hair.
The left side of the hair is cut. It is used as a guide and a cut to the left front by pulling hair at 90 degrees by moving the hair between the fingers to the ends of the hair until reaching the desired length.
The right side is removed by removing the right part. A small amount of hair is collected from the left front to be used as a basic lobe with the right front. The joint is inserted between the two fingers. It is pulled at a 90 ° angle. And subtracts the remainder of the right part with the help of the underlying chord.
Determining the length of the upper part: Removing the upper layer, leaving it to hang over the middle layer of hair, and using the bottom layers to determine the length of the top layer. The length of the upper layer differs from the middle between 2-4 inches in long hair, and half to one inch in short hair.
Cut the top layer by collecting a small chisel at the top of the front, and pull the claw by measuring the angle of 90 degrees between the fingers to the ends of the hair until reaching the point to be cut, and then cut the excess of the hair and remaining of the cone with the help of the previous truncheon as a basic.

The story of the story of the low-heeled tail ligament of the long hair

If the lady’s budget does not allow her to go to the hairdressing shops, she can cut her long hair herself in several ways, including this method, which gives a round shape of the back, and the way is:

Start with clean, damp hair.
Divide hair over the top of the head from the middle, use a high-tooth comb to do it, and comb the hair on the sides well.
Pull the hair using the comb to ensure its smoothness and back shape, and tie a hair band at the neck, making sure that there is no tangled hair using the comb, and make sure that the tie in the middle of the head and low at the neck.
The hair is tied with a hair band under the first tie and above the length to be cut.
Lift the hair gently up, then bring forward without removing the beginning of the tail tie from the neck.
Cut the hair tied under the second tie with small cutting movements, not cut once.
Remove the ligaments and move the hair and comb to see any unevenness in its length.
If unevenness is observed, hair is not cut shorter but the appendage is trimmed by re-linking the hair to the tail of the horse again and trimming it.